How To Repair A Broken Tip On A Spinning Rod

Download Article

Modern fishing rods don't break easily, but they can be fixed easily with a few unproblematic tools you may have at dwelling house. If your rod snapped, you can mend it together with a fiberglass pole and epoxy to hide the break. When ane of the guides breaks, you can remove it and wrap a new one in its place. Y'all can alter rod tips if they snap or break as well. With a little bit of work, you tin can fix your rod so it's every bit skilful every bit new!

1
Sand or cut the cleaved ends of the rod so they're flush. Use 180- or 220-dust sandpaper to smoothen the ends so they fit together easily if the rod has a clean break. If your angling rod has a jagged border, then use a pair of pair of scissors to cutting the sharp edges off of the finish of the rod so the pieces are flush. Later on you lot make your cut, use sandpaper to polish out the edges and roughen up the surface.^[1]
- Jagged edges are weaker and are more likely to break again than edges that are flush with one another.
two
Measure the circumference of the rod. Apply a flexible tape mensurate and wrap it around the broken end of your fishing rod. And then measure the circumference on the other piece of your line-fishing rod to run into if it'south skinnier. Write down your measurements so you lot know what pole size you need for fixing your rod.^[2]
- Y'all can also mensurate the diameter of the rod on both of the cleaved ends if you don't have a flexible measuring tape.
Ad
3
Cut a piece of fiberglass pole so it's most 12 in (30 cm) long. Become a fiberglass pole that has a circumference that's about ¹⁄_eight – ¹⁄₄ inch (0.32–0.64 cm) smaller than your fishing rod. Use a hacksaw to cut out a 12 in (30 cm) department of the pole and so it tin fit inside your angling rod and back up the rod without breaking.^[3]
- Y'all can buy fiberglass poles from your local hardware store. It doesn't matter what color you use since information technology volition fit inside of the rod.
- If your angling rod isn't hollow, and then using a fiberglass pole won't work. You can either try to tape your rod back together or become a new one.
Tip: You can also cut a section off of an erstwhile line-fishing pole that y'all don't use anymore if you don't have a fiberglass rod.
iv
Slide the fiberglass pole into i side of the fishing rod. Hold your rod horizontally so you can position the fiberglass pole in the rod without it sliding likewise far. Push one terminate of the fiberglass pole into the cease of the rod with the handle. Keep sliding the pole into the angling rod until at that place'southward six inches (15 cm) sticking out from the end.^[iv]
- If the pole doesn't fit snugly inside the fishing rod, and then wrap the pole with duct or masking record to brand it thicker.
5
Apply two-role epoxy to the exposed side of the fiberglass pole. Open your two-part epoxy and pour it into a bowl. Utilize a paintbrush to spread a thin layer of the epoxy on the exposed end of the fiberglass pole. Once the 2-part epoxy is mixed, work speedily and so it doesn't dry or fix before you put your rod dorsum together.^[v]
- Yous can purchase 2-office epoxy from any hardware or craft store.
6
Slide the other part of the rod onto the fiberglass and let it dry. Slowly push the other cease of your rod onto the exposed end of the fiberglass pole. Make certain the guides on the pole line up with 1 another so your line doesn't get tangled when you try using your pole again. Push the 2 pieces of the rod together so they're flush. Let the epoxy prepare overnight so it firmly adheres to the rod.^[six]
- The epoxy doesn't set up right away, and so you can all the same rotate or move the rod pieces once you slide them together.
- If whatsoever epoxy comes out of the joint while y'all're sliding the pieces together, moisture your finger and smooth out the epoxy so it isn't every bit visible.
- Wrap a layer of electric tape effectually the seam if you want an boosted layer of security.
Advertisement

1
Cut the record or thread around the broken guide with a razor blade. Utilize a straight razor blade or a arts and crafts pocketknife to remove any threading that may exist surrounding the rod guide. If information technology's difficult to remove using just a bract, so try heating the area for 3-4 seconds with a lighter to loosen any of the adhesives. Peel off the record and unwind the threading until the old, cleaved guide comes off of the rod.^[7]
- Rod guides are the circular metal pieces along the length of the rod that help keep your line straight.
- Exist careful not to heat the rod for likewise long since it could crusade damage to it.
- Don't cut into the rod with your razor, or else you could damage information technology and make it weaker.
two
Sand the rod and foot of the new guide to get ameliorate adhesion. Use 120- or 220-grit sandpaper to become rid of whatever leftover adhesive and to add tooth to the rod. Rub all the way effectually the rod on the spot where you want to place the new guide. Then, utilise your sandpaper on the foot of the guide, which is the flat part that rests against the fishing rod.^[eight]
- You tin can buy new angling guides at sporting adept stores. Make sure the new guide is the same size and style as the other guides on your line-fishing rod or else your line may snag or become tangled.
3
Tape the new guide onto the rod and then it's aligned. Printing the human foot of the new guide onto the rod so it's in line with the other guides. Rip off a thin piece of masking tape and wrap it effectually the foot and so it's held in identify. That way, you lot don't need to keep belongings it in place while you wrap it.^[ix]
- You tin likewise use super gum, but information technology will exist difficult to move or readjust once the mucilage is prepare.
4
Wrap the human foot of the guide with thread to concur it in place. Whatsoever type of thread will work for wrapping your guide onto the rod. Loop your threading around the rod so it's ^ane⁄₂ – ³⁄₄ inch (1.3–i.9 cm) from the guide's foot on the side closest to the handle. Maintain tension on the loop and outset tightly winding the thread around the rod. Make sure the thread doesn't overlap with loops you've already made and that they are flush with 1 another.^[10]
- Take the piece of tape off of the foot you've wrapped everything below it.
Tip: Use a thread that matches the color of your rod if yous want information technology to blend in.
5
Place a looped piece of thread over the wrap when there'due south ⁱ⁄₈ in (0.32 cm) left. When your wrapping is ^one⁄₈ inch (0.32 cm) from the circular office of the guide, stop winding the thread effectually the pole. Cut a divide piece of thread and so information technology's about 6 inches (15 cm) long and fold it in one-half to form a loop. Lay the second piece of thread on top of your wrapping so the loop sticks out nigh your guide.^[11]
- If you don't take any other thread, you can also employ a thin fishing line instead.
6

Wrap the terminal ⁱ⁄_eight in (0.32 cm) over the 2d piece of thread. In one case the looped piece of thread is on top of the wrapping, proceed spinning your thread around the foot of the guide. Continue wrapping the concluding ¹⁄₈ inch (0.32 cm) of the guide so the middle of the looped piece is held against the rod.^[12]
7
Feed the thread through the looped piece and pull it tight. Once y'all reach the stop of your wrapping, cutting the terminate of the thread you lot used to wrap and pull it through the middle of the loop. Pull the other finish of the looped piece down and away from the guide to pull the thread underneath the wrapping. This manner, the wrapping is secured to the rod without having to necktie a knot.^[13]
- If you lot don't want to use a looped slice of thread, you can also try tying a knot in the threading, merely it may not be every bit strong and it could exist more than hard.
8
Paint 2-part epoxy onto the thread and permit it dry out. Mix the two parts of the epoxy in a small dish with a paintbrush until they are thoroughly combined. Paint a thin layer of the epoxy over your threading so it hardens and stays in place. Keep the rod horizontal and let it dry overnight before you try using your rod again.^[14]
- Work speedily with the epoxy since it will rapidly kickoff to dry and harden in one case you mix information technology.
Advertisement

1
Rut the tip superlative of your fishing rod with a lighter to loosen the agglutinative. Set the rod horizontal so you tin easily reach the tip. Hold a lighter underneath the tip acme of the rod, which is the ringed piece at the end of the rod, and heat information technology up for four-5 seconds at a fourth dimension. In one case it's heated, endeavor pulling it off with a pair of pliers or by hand. If it doesn't come off easily, try heating information technology for some other few seconds.^[15]
- Heating the tip pinnacle helps loosen the adhesive property information technology in place and so it'southward easier to remove.
- If the tip snapped off of your rod, then you tin remove the former tip acme from the broken piece or yous can skip this pace.
two

Smooth the tip of the rod with sandpaper to remove any shards. Rub the exposed tip of the rod with 120- or 220-grit sandpaper to smooth information technology out. Rotate the rod around the sandpaper until the tip is smoothen and affluent. It's okay if there are small chafe marks on the rod tip since it volition accept better adhesion to the new tip acme.^[xvi]

Tip: If sandpaper isn't plenty to remove the shards on the end of your fishing rod, then carefully cut off the ends with a pair of scissors.
iii
Cut pieces of rod cement into strips that fit inside your new tip top. Rod cement is an adhesive that comes in a solid block and is used for fishing rods to hold guides and tips in place. Use a razor or craft knife to cutting out pocket-size strips of the rod cement so they fit inside the hollow bedroom on your rod tip top.^[17]
- You can buy rod cement and new tip tops from your local sporting goods store or online.
4

Melt the rod cement inside the tip elevation with your lighter. Hold the new tip superlative with a pair of pliers and put the pieces of rod cement in the hollow tube at the end of it. Employ your lighter to heat the rod cement for 4-five seconds and melt it so yous can attach it to your rod. Once the rod cement is melted, work quickly so it doesn't solidify again.^[eighteen]
5
Slide the tip top onto your rod so it lines up with the guides and permit it dry. While the cement is withal hot, slide it onto the tip of your rod and rotate it and then the ring is in line with the other guides. Wipe away any excess rod cement with a piece of newspaper towel and let it set for at least 1-two hours. Once the cement is dry, your rod is prepare to utilise!^[19]
- If you need to accommodate or reposition the tip top afterward the cement is dry, then heat information technology once more for 3-4 seconds with your lighter.
Ad

Add together New Question

Question

Where exercise I purchase epoxy resin gum?

At any habitation comeback or hardware shop.

Ask a Question

200 characters left

Include your electronic mail accost to get a message when this question is answered.

Submit

Have your rod to a line-fishing supply shop or a repair person if you have trouble fixing it on your own.
If you need to fix a snapped rod in an emergency, overlap the pieces past half-dozen inches (15 cm) and tape them together tightly.^[20]

Thanks for submitting a tip for review!

Don't hold a flame against your rod longer than a few seconds or else y'all could permanently damage the rod.
Be conscientious while working with razor blades so you don't accidentally cut yourself.

Things You lot'll Need

Pair of scissors
Sandpaper
Record mensurate
Fiberglass pole
Hacksaw
2-part epoxy
Bowl
Paintbrush
Electrical tape (optional)

Razor blade
Lighter
Sandpaper
Masking tape
Rod guides
Thread
2-function epoxy
Dish
Paintbrush

Lighter
Pliers
Sandpaper
Rod cement
Craft knife
Rod tip superlative

Almost This Commodity

Article Summary X

To fix a snapped fishing rod, attempt using a fiberglass pole and some epoxy. Showtime, sand the snapped edges to brand them flush. Smooth edges are stronger and less likely to interruption. Cut a 12 inch long slice of fiberglass pole using a hacksaw. Slide one terminate of the pole into your angling rod until there are 6 inches sticking out. In one case the fiberglass pole fits snugly into the rod, apply epoxy to the exposed end using a paintbrush. Connect the second half of the broken rod to the fiberglass pole and let the epoxy set up. To replace the rod guide, showtime, remove any threading from effectually the guide using a craft knife. Align the new guide onto the rod and use record to hold it in place. Wrap the new thread over the guide and then cover information technology in epoxy to set information technology. For more ideas on fixing a broken fishing rod, similar how to change a rod tip, read on.

Did this summary aid you?

Thanks to all authors for creating a folio that has been read 208,230 times.